MICROBOT MOTOR DRIVER

The minimum supply voltage allowed is 7V, so you can use also two-cell LiPo batteries 7. We will send you a mail when the product becomes available again Error during request registration Not available. The Dual DC Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper motor, controlling the speed and direction of each one independently. To avoid dangerous overheating condition you can use the integrated I2C digital temperature sensor mounted close to the L chip. This board also provides direction LED indicators for both channels; this is very usefull during setup stage to verify the firmware behaviour also without appling a real motor to the output. To optimize the response to RC commands you also have the calibration function on the receiver signals.

Uploader: Kagagis
Date Added: 11 November 2008
File Size: 58.80 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 46183
Price: Free* [*Free Regsitration Required]

All orders after this time will be shipped again from The sensor is the integrated circuit TCN75A and you can refer to its datasheet to better understanding its communication microbbot. The logic of the Dual DC Motor Shield is powered directly from the Arduino board, whereas motor outputs can be powered both from Arduino Vin pin or from external power source, even if it is strongly encouraged to use external power supply.

We will send you a mail when the product becomes available again Error during request registration Not available. Specifications Supply voltage 7 – 30V Supply current logic 24mA typ.

Cookies help us deliver our services. To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; motor velocity regulation is obtained applying to these pins a PWM signal with a 20KHz max.

Related Drivers  ASUS USB-N13 USB NETWORK ADAPTER DRIVER

Make Dumb Devices Smart

On this shield the selection of the power motot for motor outputs is accomplished by a jumper. This board also provides direction LED indicators for both channels; this is very usefull during setup mtor to verify the firmware behaviour also without appling a real motor to the output. The Easy Motor Controller provides two separate power supplies, one for the motor and the other one for the logic part; the latter can be pulled out through a jumper directly jotor that of the motor or alternatively from the BEC circuit of the RC receiver.

The Driver IC may become very hot when working with current more than 1A. The minimum supply voltage allowed is 7V, so you can use also two-cell LiPo batteries 7.

It mitor a high voltage, high current dual fullbridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays,solenoids, DC and stepping motors. Microbot Easy Motor Controller Microbot. We would like to ask you to consider this in your order planning! Moving the jumper from one side to the other the power source can be changed.

It is based on the famous integrated circuit L, producted by STMicroelectronics; the L is an integrated monolithic circuit in a PowerSO20 package.

Maggiori informazioni Read more.

Dual DC Motor Shield

In fact when the L chip works at high current values it may become very hot and this heat can flow through all the shield. Microbot Easy Motor Controller.

Add to project More from Microbot. The Easy Motor Controller allows to control the speed and the direction of rotation of a DC motor through three different possible inputs: View additional product data.

Related Drivers  ASUS NETTVERKSKORT DRIVER

For the I2C communication, there are two different slave addresses selectable through a jumper, and in this way it is possible to use two Easy Motor Controllers on the same serial line, and then control them by using a single external controller.

The maximum supply voltage supported by this board is 46V. To optimize the response to RC commands you also have the calibration function on the receiver signals. The Dual DC Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper motor, controlling the speed and direction of each one independently.

It has direction leds for help testing operations.

Dual DC Motor Shield

This powerfull DC motor driver can drive motor micdobot to 30V and 4Amax. We will send you a mail when the product becomes available again Error during request registration Not available. Description The Dual DC Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper motor, controlling mictobot speed and direction of each one independently.

Supply voltage for motors 46Vmax. This product is currently not available. By using our services, you agree to our use of cookies. Cookies help us deliver our services.

Add to shopping cart. Do you need a written offer before ordering?